「玄箱PROパッチ適用」の編集履歴（バックアップ）一覧はこちら
「玄箱PROパッチ適用」(2007/05/28 (月) 10:12:52) の最新版変更点
追加された行は緑色になります。
削除された行は赤色になります。
**玄箱PROパッチ適用
私のようにswat不具合を抱えた玄箱PROを持っている場合は必要になる作業です。ここではTFTPを使用したパッチ適用（ファームウェア・バージョンアップ）です。これもシリアルコンソールなしにはできません。
・TFTPサーバー Poor TFTP Server for WIN32をダウンロードして展開
・ptftp32.exeを実行
・Timeoutは60秒に設定しておく
・同じディレクトリにinitrd.buffaloとuImage.buffaloを配置しておく
・シリアルコンソールからリブートする
> KUROBOX-PRO:~# reboot
・PCのアドレスが192.168.1.4でさっき玄箱PROをブートしたときのアドレスが192.168.1.12だったのでserveripにはPCのアドレス、ipaddrには玄箱PROのアドレスを設定
> Marvell>> setenv serverip 192.168.1.4
> Marvell>> setenv ipaddr 192.168.1.12
> Marvell>> tftp $(default_kernel_addr) $(kernel)
> Using egiga0 device
> TFTP from server 192.168.1.4; our IP address is 192.168.1.12
> Filename 'uImage.buffalo'.
> Load address: 0x100000
> Loading: #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> ###############
> done
> Bytes transferred = 1736612 (1a7fa4 hex)
> Marvell>> setenv bootargs '$(bootargs_base) $(bootargs_root) rw
> initrd=0x02000040,20M panic=5 $(buffalo_ver)'
> Marvell>> bootm $(default_kernel_addr) $(default_initrd_addr)
> <<stop_sound>>
> ## Booting image at 00100000 ...
> Image Name: Linux-2.6.12.6-arm1
> Created: 2007-04-10 13:45:13 UTC
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1736548 Bytes = 1.7 MB
> Load Address: 00008000
> Entry Point: 00008000
> Verifying Checksum ... OK
> OK
> ## Loading Ramdisk Image at 02000000 ...
> Image Name: initrd
> Created: 2007-04-10 13:46:52 UTC
> Image Type: ARM Linux RAMDisk Image (gzip compressed)
> Data Size: 19286692 Bytes = 18.4 MB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... Bad Data CRC
> bootm fail.
> <<system_not_found>>
> Using egiga0 device
> TFTP from server 192.168.1.4; our IP address is 192.168.1.12
> Filename 'uImage.buffalo'.
> Load address: 0x100000
> Loading: #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> ###############
> done
> Bytes transferred = 1736612 (1a7fa4 hex)
> Using egiga0 device
> TFTP from server 192.168.1.4; our IP address is 192.168.1.12
> Filename 'initrd.buffalo'.
> Load address: 0x2000000
> Loading: #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> ##############################################################
> done
> Bytes transferred = 19286756 (1264ae4 hex)
> <<stop_sound>>
> ## Booting image at 00100000 ...
> Image Name: Linux-2.6.12.6-arm1
> Created: 2007-04-10 13:45:13 UTC
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1736548 Bytes = 1.7 MB
> Load Address: 00008000
> Entry Point: 00008000
> Verifying Checksum ... OK
> OK
> ## Loading Ramdisk Image at 02000000 ...
> Image Name: initrd
> Created: 2007-04-10 13:46:52 UTC
> Image Type: ARM Linux RAMDisk Image (gzip compressed)
> Data Size: 19286692 Bytes = 18.4 MB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
>
> Starting kernel ...
>
> arg:console=ttyS0,115200 root=/dev/sda2 rw panic=5 rw initrd=0x02000040,20M
> panic=5 BOOTVER=1.091
> CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
> Uncompressing Linux........................................................
> ......................................................... done, booting the
> kernel.
> Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release)
> (CodeSourcery
> ARM 2005q3-2)) #27 Tue Apr 10 22:47:16 JST 2007
> CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
> CPU0: D VIVT write-back cache
> CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
> CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
> Machine: MV-88fxx81
> Using UBoot passing parameters structure
> Sys Clk = 250000000, Tclk = 166664740
> Memory policy: ECC disabled, Data cache writeback
> Built 1 zonelists
> Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw panic=5 rw
> initrd=0x02000040,20M panic=5 BOOTVER=1.091
> PID hash table entries: 1024 (order: 10, 16384 bytes)
> Console: colour dummy device 80x30
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Memory: 128MB 0MB 0MB 0MB = 128MB total
> Memory: 105600KB available (3037K code, 426K data, 112K init)
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> checking if image is initramfs...it isn't (no cpio magic); looks like an
> initrd
> Freeing initrd memory: 20480K
> NET: Registered protocol family 16
> serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
> config_device_cs Error : Unknown board
>
> CPU Interface
> -------------
> SDRAM_CS0 ....base 00000000, size 128MB
> SDRAM_CS1 ....disable
> SDRAM_CS2 ....disable
> SDRAM_CS3 ....disable
> PEX0_MEM ....base e0000000, size 128MB
> PEX0_IO ....base f2000000, size 1MB
> PCI0_MEM ....base e8000000, size 128MB
> PCI0_IO ....base f2100000, size 1MB
> INTER_REGS ....base f1000000, size 1MB
> DEVICE_CS0 ....base fa000000, size 2MB
> DEVICE_CS1 ....base f4000000, size 32MB
> DEVICE_CS2 ....base fa800000, size 1MB
> DEV_BOOCS ....base ff800000, size 8MB
> CRYPTO ENG ....no such
> Flash bankwidth 1, base ff800000, size 400000
> KUROBOX FLASH size 4096[KB]
>
> Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_
> BOARD_KUROBOX Soc: 88F5182 A2
>
> Detected Tclk 166664740 and SysClk 250000000
> Marvell USB EHCI Host controller #0: c3403bc0
> Marvell USB EHCI Host controller #1: c3403a40
> pexBarOverlapDetect: winNum 2 overlap current 0
> mvPexInit:Warning :Bar 2 size is illigal
> it will be disabled
> please check Pex and CPU windows configuration
> PCI: bus0: Fast back to back transfers enabled
> PCI: bus1: Fast back to back transfers enabled
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> Use the XOR engines (offloading) for enhancing the following functions:
> o RAID 5 Xor calculation
> o kernel memcpy
> o kenrel memzero
> o copy user to/from kernel buffers
> Number of XOR engines to use: 2
> cesadev_init(c00122e4)
> Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
> inotify device minor=63
> JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
> SGI XFS with no debug enabled
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
> ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
> loop: loaded (max 8 devices)
> Marvell Gigabit Ethernet Driver 'egiga':
> o Ethernet descriptors in DRAM
> o DRAM SW cache-coherency
> o Checksum offload enabled
> o Loading network interface ** egiga_init_module (10)
> 'eth0'
> Intergrated Sata device found
> scsi0 : Marvell SCSI to SATA adapter
> scsi1 : Marvell SCSI to SATA adapter
> Vendor: Hitachi Model: HDT725050VLA360 Rev: V56O
> Type: Direct-Access ANSI SCSI revision: 03
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> SCSI device sda: drive cache: write back
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 sda3 sda4
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> physmap flash device: 400000 at ff800000
> Found: SST 39LF020
> phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
> number of JEDEC chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> RedBoot partition parsing not available
> Debug nand_scan : nand_flash_ids[i].pagesize is exist
> Debug nand_scan : mtd->erasesize=0x00020000
> Debug nand_scan : mtd->oobblock=0x00000800
> Debug nand_scan : mtd->oobsize=0x00000040
> NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3
> V 8-bit)
> Scanning device for bad blocks
> Bad eraseblock 854 at 0x06ac0000
> Using static partition definition
> Creating 3 MTD partitions on "nand_mtd":
> 0x00000000-0x00400000 : "uImage"
> 0x00400000-0x04400000 : "rootfs"
> 0x04400000-0x10000000 : "extra"
> usbmon: debugs is not available
> ehci_platform ehci_platform.4523: EHCI Host Controller
> ehci_platform ehci_platform.4523: new USB bus registered, assigned bus numb
> er 1
> ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
> ehci_platform ehci_platform.4523: park 0
> ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10
> Dec 2004
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 1 port detected
> ehci_platform ehci_platform.16781: EHCI Host Controller
> ehci_platform ehci_platform.16781: new USB bus registered, assigned bus num
> ber 2
> ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
> ehci_platform ehci_platform.16781: park 0
> ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 1
> 0 Dec 2004
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 1 port detected
> USB Universal Host Controller Interface driver v2.2
> Initializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.01:USB HID core driver
> mice: PS/2 mouse device common for all mice
> md: raid0 personality registered as nr 2
> md: raid1 personality registered as nr 3
> md: raid5 personality registered as nr 4
> raid5: measuring checksumming speed
> arm4regs : 308.800 MB/sec
> 8regs : 217.600 MB/sec
> 32regs : 252.400 MB/sec
> raid5: using function: arm4regs (308.800 MB/sec)
> md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
> Buffalo Platform Linux Driver(Light) 0.01 installed.
> MICON ctrl (C) BUFFALO INC. V.1.00 installed.
> Kernel event proc (C) BUFFALO INC. V.1.00 installed.
> MICON V2 (C) BUFFALO INC. V.1.00 installed.
> NET: Registered protocol family 2
> IP: routing cache hash table of 1024 buckets, 8Kbytes
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> md: Autodetecting RAID arrays.
> md: autorun ...
> md: ... autorun DONE.
> RAMDISK: Compressed image found at block 0
> VFS: Mounted root (ext2 filesystem).
> ---- in linuxrc ---
> proc mount success
> libbuffalo mount success
> -RamdiskRoot-
> -- linuxrc finished. --
> Freeing init memory: 112K
> init started: BusyBox v1.2.2 (2007.01.15-11:18+0000) multi-call binary
> Starting pid 242, console /dev/ttyS0: '/etc/init.d/rcS'
> --- rcStart (initrd) ---
> ===== Starting MountSystemFolders =====
> mounting procfs ... [Success]
> mounting sysfs ... [Success]
> remounting rootfs ... [Success]
> mounting all devices ... [Success]
>
> --MountNandDevice--
>
> ===== Starting Kevent.sh =====
> [Success]
>
>
> ===== Starting networking.sh =====
> Deconfiguration network interface: lo eth0
> killall: dhcpcd: no process killed
> create network files..
> IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
> killall: dhcpcd: no process killed
> route: SIOC[ADD|DEL]RT: No such process
> Configuration network interface: lo eth0
> requesting DHCP tout=30[s]
> eth0: link down
> eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
> /etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info new
> dhcpcd.exe: interface eth0 has been configured with new IP=192.168.1.12
> hostname is setted to KUROBOX-PRO
> [Success]
>
>
> ===== Starting sethostname.sh =====
> hostname is setted to KUROBOX-PRO
> [Success]
>
>
> ===== Starting clientUtil_servd.sh =====
> Starting clientUtil_server:starting on eth0
> start at debug mode
> clientUtil_server Ver.1.01
> listen device name = eth0
> [Success]
>
> Starting pid 484, console /dev/ttyS0: '/sbin/getty'
>
> KUROBOX-PRO login:
> }
・ログインして更新コマンドを実行する実行
> ~ # update_mtd.sh all
> ***** Cleaning and collect badlist /dev/mtd1 *****
> ***** copying /boot/uImage.buffalo to /dev/mtd1 *****
> ***** Cleaning /dev/mtdchar2 *****
> ***** Writing /boot/nandrootfs.jffs2 to /dev/mtdchar2 *****
> ***** copying /boot/u-boot.bin to /dev/mtd0 *****
> 480+1 records in
> 480+1 records out
> ***** Cleaning /dev/mtdchar3 *****
> Done.
> ~ #
・リブートする
> ~ # reboot
> Orion1 CPU = Low
>
> === KURO U-Boot. ===
> ** LOADER **
> ** KUROBOX BOARD: KURO_BOX LE (CFG_ENV_ADDR=fffff000)
>
>
> U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY
>
> DRAM CS[0] base 0x00000000 size 128MB
> DRAM Total size 128MB
> [256kB@fffc0000] Flash: 256 kB
> Addresses 20M - 0M are saved for the U-Boot usage.
> Mem malloc Initialization (20M - 16M): Done
> NAND: 256 MB
>
> Soc: 88F5182 A2
> CPU: ARM926 (Rev 0) running @ 500Mhz
> Orion 1 streaming disabled
> SysClock = 250Mhz , TClock = 166Mhz
>
>
> USB 0: host mode
> USB 1: host mode
> PCI 0: PCI Express Root Complex Interface
> PCI 1: Conventional PCI, speed = 33000000
> Net: egiga0 [PRIME]
> Using 88E1118 phy
> Found boot image
> hit any key to switch tftp boot.
> Hit any key to stop autoboot: 0
> <<system_bootend>>
> Hit any key to stop autoboot: 0
>
> Loading from device 0: <NULL> at 0xfa000000 (offset 0x20000)
> Image Name: Linux-2.6.12.6-arm1
> Created: 2007-04-10 13:45:13 UTC
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1736548 Bytes = 1.7 MB
> Load Address: 00008000
> Entry Point: 00008000
> <<stop_sound>>
> ## Booting image at 00100000 ...
> Image Name: Linux-2.6.12.6-arm1
> Created: 2007-04-10 13:45:13 UTC
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1736548 Bytes = 1.7 MB
> Load Address: 00008000
> Entry Point: 00008000
> Verifying Checksum ... OK
> OK
>
> Starting kernel ...
>
> arg:console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.091
> CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
> Uncompressing Linux........................................................
> ......................................................... done, booting the
> kernel.
> Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (C
> odeSourcery
> ARM 2005q3-2)) #27 Tue Apr 10 22:47:16 JST 2007
> CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
> CPU0: D VIVT write-back cache
> CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
> CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
> Machine: MV-88fxx81
> Using UBoot passing parameters structure
> Sys Clk = 250000000, Tclk = 166664740
> Memory policy: ECC disabled, Data cache writeback
> Built 1 zonelists
> Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BO
> OTVER=1.091
> PID hash table entries: 1024 (order: 10, 16384 bytes)
> Console: colour dummy device 80x30
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Memory: 128MB 0MB 0MB 0MB = 128MB total
> Memory: 126208KB available (3037K code, 426K data, 112K init)
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> NET: Registered protocol family 16
> serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
> config_device_cs Error : Unknown board
>
> CPU Interface
> -------------
> SDRAM_CS0 ....base 00000000, size 128MB
> SDRAM_CS1 ....disable
> SDRAM_CS2 ....disable
> SDRAM_CS3 ....disable
> PEX0_MEM ....base e0000000, size 128MB
> PEX0_IO ....base f2000000, size 1MB
> PCI0_MEM ....base e8000000, size 128MB
> PCI0_IO ....base f2100000, size 1MB
> INTER_REGS ....base f1000000, size 1MB
> DEVICE_CS0 ....base fa000000, size 2MB
> DEVICE_CS1 ....base f4000000, size 32MB
> DEVICE_CS2 ....base fa800000, size 1MB
> DEV_BOOCS ....base ff800000, size 8MB
> CRYPTO ENG ....no such
> Flash bankwidth 1, base ff800000, size 400000
> KUROBOX FLASH size 4096[KB]
>
> Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_BO
> ARD_KUROBOX Soc: 88F5182 A2
>
> Detected Tclk 166664740 and SysClk 250000000
> Marvell USB EHCI Host controller #0: c04e4b00
> Marvell USB EHCI Host controller #1: c04e4a40
> pexBarOverlapDetect: winNum 2 overlap current 0
> mvPexInit:Warning :Bar 2 size is illigal
> it will be disabled
> please check Pex and CPU windows configuration
> PCI: bus0: Fast back to back transfers enabled
> PCI: bus1: Fast back to back transfers enabled
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> Use the XOR engines (offloading) for enhancing the following functions:
> o RAID 5 Xor calculation
> o kernel memcpy
> o kenrel memzero
> o copy user to/from kernel buffers
> Number of XOR engines to use: 2
> cesadev_init(c00122e4)
> Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
> inotify device minor=63
> JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
> SGI XFS with no debug enabled
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
> ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
> loop: loaded (max 8 devices)
> Marvell Gigabit Ethernet Driver 'egiga':
> o Ethernet descriptors in DRAM
> o DRAM SW cache-coherency
> o Checksum offload enabled
> o Loading network interface ** egiga_init_module (10)
> 'eth0'
> Intergrated Sata device found
> scsi0 : Marvell SCSI to SATA adapter
> scsi1 : Marvell SCSI to SATA adapter
> Vendor: Hitachi Model: HDT725050VLA360 Rev: V56O
> Type: Direct-Access ANSI SCSI revision: 03
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> SCSI device sda: drive cache: write back
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 sda3 sda4
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> physmap flash device: 400000 at ff800000
> Found: SST 39LF020
> phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
> number of JEDEC chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> RedBoot partition parsing not available
> Debug nand_scan : nand_flash_ids[i].pagesize is exist
> Debug nand_scan : mtd->erasesize=0x00020000
> Debug nand_scan : mtd->oobblock=0x00000800
> Debug nand_scan : mtd->oobsize=0x00000040
> NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3
> V 8-bit)
> Scanning device for bad blocks
> Bad eraseblock 854 at 0x06ac0000
> Using static partition definition
> Creating 3 MTD partitions on "nand_mtd":
> 0x00000000-0x00400000 : "uImage"
> 0x00400000-0x04400000 : "rootfs"
> 0x04400000-0x10000000 : "extra"
> usbmon: debugs is not available
> ehci_platform ehci_platform.4523: EHCI Host Controller
> ehci_platform ehci_platform.4523: new USB bus registered, assigned bus numb
> er 1
> ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
> ehci_platform ehci_platform.4523: park 0
> ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10
> Dec 2004
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 1 port detected
> ehci_platform ehci_platform.16781: EHCI Host Controller
> ehci_platform ehci_platform.16781: new USB bus registered, assigned bus num
> ber 2
> ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
> ehci_platform ehci_platform.16781: park 0
> ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 1
> 0 Dec 2004
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 1 port detected
> USB Universal Host Controller Interface driver v2.2
> Initializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.01:USB HID core driver
> mice: PS/2 mouse device common for all mice
> md: raid0 personality registered as nr 2
> md: raid1 personality registered as nr 3
> md: raid5 personality registered as nr 4
> raid5: measuring checksumming speed
> arm4regs : 304.000 MB/sec
> 8regs : 215.200 MB/sec
> 32regs : 249.200 MB/sec
> raid5: using function: arm4regs (304.000 MB/sec)
> md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
> Buffalo Platform Linux Driver(Light) 0.01 installed.
> MICON ctrl (C) BUFFALO INC. V.1.00 installed.
> Kernel event proc (C) BUFFALO INC. V.1.00 installed.
> MICON V2 (C) BUFFALO INC. V.1.00 installed.
> NET: Registered protocol family 2
> IP: routing cache hash table of 1024 buckets, 8Kbytes
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> md: Autodetecting RAID arrays.
> md: autorun ...
> md: ... autorun DONE.
> Empty flash at 0x00df85f8 ends at 0x00df8800
> VFS: Mounted root (jffs2 filesystem).
> Freeing init memory: 112K
> --- rcStart (NANDroot) ---
> ===== Starting MountSystemFolders =====
> mounting procfs ... [Success]
> mounting sysfs ... [Success]
> mouting usbfs ... [Success]
> remouting rootfs ... [Success]
> mounting all devices ... [Success]
>
>
> ===== Starting checkroot.sh =====
> rm: /var/lock/perfmon: is a directory
> rm: /var/lock/printing: is a directory
> rm: /var/lock/subsys: is a directory
> [Success]
>
>
> ===== Starting Kevent.sh =====
> [Success]
>
>
> ===== Starting mount_share.sh =====
> Mounting /dev/sda4 on /mnt/disk1 as a xfs file system.
> XFS mounting filesystem sda4
> Starting XFS recovery on filesystem: sda4 (dev: sda4)
> Ending XFS recovery on filesystem: sda4 (dev: sda4)
> Success.
>
> Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
> Success.
>
> [Success]
>
>
> ===== Starting sethostname.sh =====
> hostname is setted to KUROBOX-PRO
> [Success]
>
>
> ===== Starting networking.sh =====
> create network files..
> IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
> killall: dhcpcd: no process killed
> route: SIOC[ADD|DEL]RT: No such process
> Configuration network interface: lo eth0
> requesting DHCP tout=30[s]
> eth0: link down
> eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
> /etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info up
> dhcpcd.exe: interface eth0 has been configured with old IP=192.168.1.12
> hostname is setted to KUROBOX-PRO
> [Success]
>
>
> ===== Starting httpd.sh =====
> [Success]
>
>
> ===== Starting telnet.sh =====
> [Success]
>
>
> ===== Starting inetd.sh =====
> [Success]
>
>
> ===== Starting smb.sh =====
> $Starting SMB services:
> $Starting NMB services:
> [Success]
>
>
> ===== Starting clientUtil_servd.sh =====
> Starting clientUtil_server:starting on eth0
> [Success]
>
>
> ===== Starting bootcomplete.sh =====
> [Success]
>
>
> ===== Starting FanController.sh =====
> [Success]
>
>
> ===== Starting boss.sh =====
>
> ...''''..
> '-~~(~~'' .~<shDBDhz+(-.
> .~+sDDBNBDhhszDBNNNNBNNNBDs<-
> ~sBNNNNNNNNNNNNNNNNNNNNNNNNNBs<'
> -=DNNBNNNNNNNNNNNNNNNNNBNNNNNNNNBz<'
> .~zNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNz~
> '~hBNNNNBNNNNNNNNNNNNNNNNNNNNNNNNNNNNNND+'
> (hNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNBs-
> .~zNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNBNNBNNNNNNBs
> ~sBNNNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNNNNNNNz
> (+DNNNNNNNNNNNNNNNNNNNNNNDzNNNNNhzDNNBNNNNNNNNBs
> (sNNNNNNNNNNNNNNNNNNNNNNB=~hNNNN=~(sDNNNNNNNNNND
> (+DNNNNNNNNNNNNNNNNNNNNNNs'.=NNNNz- '(zDNNNNNNNNNz
> ~=BNNNNNNNNNNNNNNNNNNNNND- .=BNNNN<. .(hNNNNNNNNB
> ~sNNNNNNNNNNNNNNNNNNNNND+. .+BNNNN+' ~sBNNNNNNN
> (zNNNNNNNNNNNNNNNNNNNNND' ..+BNBNB=- .+BNNNNNNh
> (zNNNNNNNNNNNNNNNNNNNBB= . 'hNBBNs+- '+DNNNBND
> (sNNNNNNNNNNNNNNNNNNNND( -DhDBN+<- . '=NNNNNB
> ~+DNNBNNNNNNNNNNNNNNNNz' '=D=Dhh+(' . ~DBNNNB
> ~(sNNNNNNNNNNNNNNNNNNNz. -hs(zz+<(' . .=NNNNN
> ~=NNBBBBNNNNNNNNNNNNB= '==-=+s((~. .~BNNNB
> ~=Nhs<+++hNNNNNNNNBz<- .~=-.s(+-(- 'hBNND
> =Ds+hz( ~hNNNNNNND+'..-+'.-((('<~''... -hNNNNDs
> ~+z(BN=. .<BNNNNBhhDD=+<~. ~-=shBBDhz+(' -sBNNNBBNBz
> ~(=z(BD- '~~hBNNNs~-(<zDDs+~(shzssszDBNDh=<<sBNNNNNNNBN
> ~~+s<z=.-zh~sNNND<. .''<zhhh==shDBNNNNNNNBDDNNNNNNNNNh
> ~~<ss+<.zBBs~zND+' ..-+zDBNNNNNNNNNNNhzNNNNNNNNND+
> ~~(=h<<'+DBz-sBs~ . (BBNNNNNNNNNz-<BBNNBNNND=
> ~(~<zss(('(z<sD+' ~DNNNNNNNNNz~ 'sNNNNNNDs
> ~(=Ds=<...-(h<. . ..<BNNNNNNNNz~ -hNNNBh
> ~(hNs(. =- .=BNNNNNBNs- .(hs==
> ''<BNz~ '. .(hBNNBDz<' .~''-
> -hNNh(. '.. .'<<(++~ . -''.
> 'hBNB+' ' -+('. .-''.
> 'zDNz( '. ~+<-'''..''. .-.
> ..~(-. .'. .~+(. ..''--''.
> ''. .'+<~ '~.
> ..... .-' .'---(~~~(<~.
> ..'. .((---'-~~(~
> .'. '+s=(-'-(+. < Let's start a KURO-BOX!
> .... .(hBDzDD=. and have a fun time...
> ..'.. .'<sDh+.
> .''.. . ..-- .
> ..''.. ...
> ....... .'.
> ..''..'-'..
> ...
>
>
> [Success]
>
>
> KUROUTOSHIKOU KUROBOX Series KUROBOX/PRO(KOSHO)
> KUROBOX-PRO login:
**玄箱PROパッチ適用
私のようにswat不具合を抱えた玄箱PROを持っている場合は必要になる作業です。ここではTFTPを使用したパッチ適用（ファームウェア・バージョンアップ）です。これもシリアルコンソールなしにはできません。
・TFTPサーバー Poor TFTP Server for WIN32をダウンロードして展開
・ptftp32.exeを実行
・Timeoutは60秒に設定しておく
・同じディレクトリにinitrd.buffaloとuImage.buffaloを配置しておく
・シリアルコンソールからリブートする
> KUROBOX-PRO:~# reboot
・PCのアドレスが192.168.1.4でさっき玄箱PROをブートしたときのアドレスが192.168.1.12だったのでserveripにはPCのアドレス、ipaddrには玄箱PROのアドレスを設定
> Marvell>> setenv serverip 192.168.1.4
> Marvell>> setenv ipaddr 192.168.1.12
> Marvell>> tftp $(default_kernel_addr) $(kernel)
> Using egiga0 device
> TFTP from server 192.168.1.4; our IP address is 192.168.1.12
> Filename 'uImage.buffalo'.
> Load address: 0x100000
> Loading: #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> ###############
> done
> Bytes transferred = 1736612 (1a7fa4 hex)
> Marvell>> setenv bootargs '$(bootargs_base) $(bootargs_root) rw
> initrd=0x02000040,20M panic=5 $(buffalo_ver)'
> Marvell>> bootm $(default_kernel_addr) $(default_initrd_addr)
> <<stop_sound>>
> ## Booting image at 00100000 ...
> Image Name: Linux-2.6.12.6-arm1
> Created: 2007-04-10 13:45:13 UTC
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1736548 Bytes = 1.7 MB
> Load Address: 00008000
> Entry Point: 00008000
> Verifying Checksum ... OK
> OK
> ## Loading Ramdisk Image at 02000000 ...
> Image Name: initrd
> Created: 2007-04-10 13:46:52 UTC
> Image Type: ARM Linux RAMDisk Image (gzip compressed)
> Data Size: 19286692 Bytes = 18.4 MB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... Bad Data CRC
> bootm fail.
> <<system_not_found>>
> Using egiga0 device
> TFTP from server 192.168.1.4; our IP address is 192.168.1.12
> Filename 'uImage.buffalo'.
> Load address: 0x100000
> Loading: #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> ###############
> done
> Bytes transferred = 1736612 (1a7fa4 hex)
> Using egiga0 device
> TFTP from server 192.168.1.4; our IP address is 192.168.1.12
> Filename 'initrd.buffalo'.
> Load address: 0x2000000
> Loading: #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> #################################################################
> ##############################################################
> done
> Bytes transferred = 19286756 (1264ae4 hex)
> <<stop_sound>>
> ## Booting image at 00100000 ...
> Image Name: Linux-2.6.12.6-arm1
> Created: 2007-04-10 13:45:13 UTC
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1736548 Bytes = 1.7 MB
> Load Address: 00008000
> Entry Point: 00008000
> Verifying Checksum ... OK
> OK
> ## Loading Ramdisk Image at 02000000 ...
> Image Name: initrd
> Created: 2007-04-10 13:46:52 UTC
> Image Type: ARM Linux RAMDisk Image (gzip compressed)
> Data Size: 19286692 Bytes = 18.4 MB
> Load Address: 00000000
> Entry Point: 00000000
> Verifying Checksum ... OK
>
> Starting kernel ...
>
> arg:console=ttyS0,115200 root=/dev/sda2 rw panic=5 rw initrd=0x02000040,20M
> panic=5 BOOTVER=1.091
> CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
> Uncompressing Linux........................................................
> ......................................................... done, booting the
> kernel.
> Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release)
> (CodeSourcery
> ARM 2005q3-2)) #27 Tue Apr 10 22:47:16 JST 2007
> CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
> CPU0: D VIVT write-back cache
> CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
> CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
> Machine: MV-88fxx81
> Using UBoot passing parameters structure
> Sys Clk = 250000000, Tclk = 166664740
> Memory policy: ECC disabled, Data cache writeback
> Built 1 zonelists
> Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw panic=5 rw
> initrd=0x02000040,20M panic=5 BOOTVER=1.091
> PID hash table entries: 1024 (order: 10, 16384 bytes)
> Console: colour dummy device 80x30
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Memory: 128MB 0MB 0MB 0MB = 128MB total
> Memory: 105600KB available (3037K code, 426K data, 112K init)
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> checking if image is initramfs...it isn't (no cpio magic); looks like an
> initrd
> Freeing initrd memory: 20480K
> NET: Registered protocol family 16
> serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
> config_device_cs Error : Unknown board
>
> CPU Interface
> -------------
> SDRAM_CS0 ....base 00000000, size 128MB
> SDRAM_CS1 ....disable
> SDRAM_CS2 ....disable
> SDRAM_CS3 ....disable
> PEX0_MEM ....base e0000000, size 128MB
> PEX0_IO ....base f2000000, size 1MB
> PCI0_MEM ....base e8000000, size 128MB
> PCI0_IO ....base f2100000, size 1MB
> INTER_REGS ....base f1000000, size 1MB
> DEVICE_CS0 ....base fa000000, size 2MB
> DEVICE_CS1 ....base f4000000, size 32MB
> DEVICE_CS2 ....base fa800000, size 1MB
> DEV_BOOCS ....base ff800000, size 8MB
> CRYPTO ENG ....no such
> Flash bankwidth 1, base ff800000, size 400000
> KUROBOX FLASH size 4096[KB]
>
> Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_
> BOARD_KUROBOX Soc: 88F5182 A2
>
> Detected Tclk 166664740 and SysClk 250000000
> Marvell USB EHCI Host controller #0: c3403bc0
> Marvell USB EHCI Host controller #1: c3403a40
> pexBarOverlapDetect: winNum 2 overlap current 0
> mvPexInit:Warning :Bar 2 size is illigal
> it will be disabled
> please check Pex and CPU windows configuration
> PCI: bus0: Fast back to back transfers enabled
> PCI: bus1: Fast back to back transfers enabled
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> Use the XOR engines (offloading) for enhancing the following functions:
> o RAID 5 Xor calculation
> o kernel memcpy
> o kenrel memzero
> o copy user to/from kernel buffers
> Number of XOR engines to use: 2
> cesadev_init(c00122e4)
> Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
> inotify device minor=63
> JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
> SGI XFS with no debug enabled
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
> ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
> loop: loaded (max 8 devices)
> Marvell Gigabit Ethernet Driver 'egiga':
> o Ethernet descriptors in DRAM
> o DRAM SW cache-coherency
> o Checksum offload enabled
> o Loading network interface ** egiga_init_module (10)
> 'eth0'
> Intergrated Sata device found
> scsi0 : Marvell SCSI to SATA adapter
> scsi1 : Marvell SCSI to SATA adapter
> Vendor: Hitachi Model: HDT725050VLA360 Rev: V56O
> Type: Direct-Access ANSI SCSI revision: 03
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> SCSI device sda: drive cache: write back
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 sda3 sda4
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> physmap flash device: 400000 at ff800000
> Found: SST 39LF020
> phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
> number of JEDEC chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> RedBoot partition parsing not available
> Debug nand_scan : nand_flash_ids[i].pagesize is exist
> Debug nand_scan : mtd->erasesize=0x00020000
> Debug nand_scan : mtd->oobblock=0x00000800
> Debug nand_scan : mtd->oobsize=0x00000040
> NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3
> V 8-bit)
> Scanning device for bad blocks
> Bad eraseblock 854 at 0x06ac0000
> Using static partition definition
> Creating 3 MTD partitions on "nand_mtd":
> 0x00000000-0x00400000 : "uImage"
> 0x00400000-0x04400000 : "rootfs"
> 0x04400000-0x10000000 : "extra"
> usbmon: debugs is not available
> ehci_platform ehci_platform.4523: EHCI Host Controller
> ehci_platform ehci_platform.4523: new USB bus registered, assigned bus numb
> er 1
> ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
> ehci_platform ehci_platform.4523: park 0
> ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10
> Dec 2004
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 1 port detected
> ehci_platform ehci_platform.16781: EHCI Host Controller
> ehci_platform ehci_platform.16781: new USB bus registered, assigned bus num
> ber 2
> ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
> ehci_platform ehci_platform.16781: park 0
> ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 1
> 0 Dec 2004
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 1 port detected
> USB Universal Host Controller Interface driver v2.2
> Initializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.01:USB HID core driver
> mice: PS/2 mouse device common for all mice
> md: raid0 personality registered as nr 2
> md: raid1 personality registered as nr 3
> md: raid5 personality registered as nr 4
> raid5: measuring checksumming speed
> arm4regs : 308.800 MB/sec
> 8regs : 217.600 MB/sec
> 32regs : 252.400 MB/sec
> raid5: using function: arm4regs (308.800 MB/sec)
> md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
> Buffalo Platform Linux Driver(Light) 0.01 installed.
> MICON ctrl (C) BUFFALO INC. V.1.00 installed.
> Kernel event proc (C) BUFFALO INC. V.1.00 installed.
> MICON V2 (C) BUFFALO INC. V.1.00 installed.
> NET: Registered protocol family 2
> IP: routing cache hash table of 1024 buckets, 8Kbytes
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> md: Autodetecting RAID arrays.
> md: autorun ...
> md: ... autorun DONE.
> RAMDISK: Compressed image found at block 0
> VFS: Mounted root (ext2 filesystem).
> ---- in linuxrc ---
> proc mount success
> libbuffalo mount success
> -RamdiskRoot-
> -- linuxrc finished. --
> Freeing init memory: 112K
> init started: BusyBox v1.2.2 (2007.01.15-11:18+0000) multi-call binary
> Starting pid 242, console /dev/ttyS0: '/etc/init.d/rcS'
> --- rcStart (initrd) ---
> ===== Starting MountSystemFolders =====
> mounting procfs ... [Success]
> mounting sysfs ... [Success]
> remounting rootfs ... [Success]
> mounting all devices ... [Success]
>
> --MountNandDevice--
>
> ===== Starting Kevent.sh =====
> [Success]
>
>
> ===== Starting networking.sh =====
> Deconfiguration network interface: lo eth0
> killall: dhcpcd: no process killed
> create network files..
> IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
> killall: dhcpcd: no process killed
> route: SIOC[ADD|DEL]RT: No such process
> Configuration network interface: lo eth0
> requesting DHCP tout=30[s]
> eth0: link down
> eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
> /etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info new
> dhcpcd.exe: interface eth0 has been configured with new IP=192.168.1.12
> hostname is setted to KUROBOX-PRO
> [Success]
>
>
> ===== Starting sethostname.sh =====
> hostname is setted to KUROBOX-PRO
> [Success]
>
>
> ===== Starting clientUtil_servd.sh =====
> Starting clientUtil_server:starting on eth0
> start at debug mode
> clientUtil_server Ver.1.01
> listen device name = eth0
> [Success]
>
> Starting pid 484, console /dev/ttyS0: '/sbin/getty'
>
> KUROBOX-PRO login:
> }
・ログインして更新コマンドを実行する実行
> ~ # update_mtd.sh all
> ***** Cleaning and collect badlist /dev/mtd1 *****
> ***** copying /boot/uImage.buffalo to /dev/mtd1 *****
> ***** Cleaning /dev/mtdchar2 *****
> ***** Writing /boot/nandrootfs.jffs2 to /dev/mtdchar2 *****
> ***** copying /boot/u-boot.bin to /dev/mtd0 *****
> 480+1 records in
> 480+1 records out
> ***** Cleaning /dev/mtdchar3 *****
> Done.
> ~ #
・リブートする
> ~ # reboot
> Orion1 CPU = Low
>
> === KURO U-Boot. ===
> ** LOADER **
> ** KUROBOX BOARD: KURO_BOX LE (CFG_ENV_ADDR=fffff000)
>
>
> U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY
>
> DRAM CS[0] base 0x00000000 size 128MB
> DRAM Total size 128MB
> [256kB@fffc0000] Flash: 256 kB
> Addresses 20M - 0M are saved for the U-Boot usage.
> Mem malloc Initialization (20M - 16M): Done
> NAND: 256 MB
>
> Soc: 88F5182 A2
> CPU: ARM926 (Rev 0) running @ 500Mhz
> Orion 1 streaming disabled
> SysClock = 250Mhz , TClock = 166Mhz
>
>
> USB 0: host mode
> USB 1: host mode
> PCI 0: PCI Express Root Complex Interface
> PCI 1: Conventional PCI, speed = 33000000
> Net: egiga0 [PRIME]
> Using 88E1118 phy
> Found boot image
> hit any key to switch tftp boot.
> Hit any key to stop autoboot: 0
> <<system_bootend>>
> Hit any key to stop autoboot: 0
>
> Loading from device 0: <NULL> at 0xfa000000 (offset 0x20000)
> Image Name: Linux-2.6.12.6-arm1
> Created: 2007-04-10 13:45:13 UTC
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1736548 Bytes = 1.7 MB
> Load Address: 00008000
> Entry Point: 00008000
> <<stop_sound>>
> ## Booting image at 00100000 ...
> Image Name: Linux-2.6.12.6-arm1
> Created: 2007-04-10 13:45:13 UTC
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1736548 Bytes = 1.7 MB
> Load Address: 00008000
> Entry Point: 00008000
> Verifying Checksum ... OK
> OK
>
> Starting kernel ...
>
> arg:console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.091
> CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
> Uncompressing Linux........................................................
> ......................................................... done, booting the
> kernel.
> Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (C
> odeSourcery
> ARM 2005q3-2)) #27 Tue Apr 10 22:47:16 JST 2007
> CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
> CPU0: D VIVT write-back cache
> CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
> CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
> Machine: MV-88fxx81
> Using UBoot passing parameters structure
> Sys Clk = 250000000, Tclk = 166664740
> Memory policy: ECC disabled, Data cache writeback
> Built 1 zonelists
> Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BO
> OTVER=1.091
> PID hash table entries: 1024 (order: 10, 16384 bytes)
> Console: colour dummy device 80x30
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Memory: 128MB 0MB 0MB 0MB = 128MB total
> Memory: 126208KB available (3037K code, 426K data, 112K init)
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> NET: Registered protocol family 16
> serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
> config_device_cs Error : Unknown board
>
> CPU Interface
> -------------
> SDRAM_CS0 ....base 00000000, size 128MB
> SDRAM_CS1 ....disable
> SDRAM_CS2 ....disable
> SDRAM_CS3 ....disable
> PEX0_MEM ....base e0000000, size 128MB
> PEX0_IO ....base f2000000, size 1MB
> PCI0_MEM ....base e8000000, size 128MB
> PCI0_IO ....base f2100000, size 1MB
> INTER_REGS ....base f1000000, size 1MB
> DEVICE_CS0 ....base fa000000, size 2MB
> DEVICE_CS1 ....base f4000000, size 32MB
> DEVICE_CS2 ....base fa800000, size 1MB
> DEV_BOOCS ....base ff800000, size 8MB
> CRYPTO ENG ....no such
> Flash bankwidth 1, base ff800000, size 400000
> KUROBOX FLASH size 4096[KB]
>
> Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_BO
> ARD_KUROBOX Soc: 88F5182 A2
>
> Detected Tclk 166664740 and SysClk 250000000
> Marvell USB EHCI Host controller #0: c04e4b00
> Marvell USB EHCI Host controller #1: c04e4a40
> pexBarOverlapDetect: winNum 2 overlap current 0
> mvPexInit:Warning :Bar 2 size is illigal
> it will be disabled
> please check Pex and CPU windows configuration
> PCI: bus0: Fast back to back transfers enabled
> PCI: bus1: Fast back to back transfers enabled
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> Use the XOR engines (offloading) for enhancing the following functions:
> o RAID 5 Xor calculation
> o kernel memcpy
> o kenrel memzero
> o copy user to/from kernel buffers
> Number of XOR engines to use: 2
> cesadev_init(c00122e4)
> Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
> inotify device minor=63
> JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
> SGI XFS with no debug enabled
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
> ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
> loop: loaded (max 8 devices)
> Marvell Gigabit Ethernet Driver 'egiga':
> o Ethernet descriptors in DRAM
> o DRAM SW cache-coherency
> o Checksum offload enabled
> o Loading network interface ** egiga_init_module (10)
> 'eth0'
> Intergrated Sata device found
> scsi0 : Marvell SCSI to SATA adapter
> scsi1 : Marvell SCSI to SATA adapter
> Vendor: Hitachi Model: HDT725050VLA360 Rev: V56O
> Type: Direct-Access ANSI SCSI revision: 03
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> SCSI device sda: drive cache: write back
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 sda3 sda4
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> physmap flash device: 400000 at ff800000
> Found: SST 39LF020
> phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
> number of JEDEC chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> RedBoot partition parsing not available
> Debug nand_scan : nand_flash_ids[i].pagesize is exist
> Debug nand_scan : mtd->erasesize=0x00020000
> Debug nand_scan : mtd->oobblock=0x00000800
> Debug nand_scan : mtd->oobsize=0x00000040
> NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3
> V 8-bit)
> Scanning device for bad blocks
> Bad eraseblock 854 at 0x06ac0000
> Using static partition definition
> Creating 3 MTD partitions on "nand_mtd":
> 0x00000000-0x00400000 : "uImage"
> 0x00400000-0x04400000 : "rootfs"
> 0x04400000-0x10000000 : "extra"
> usbmon: debugs is not available
> ehci_platform ehci_platform.4523: EHCI Host Controller
> ehci_platform ehci_platform.4523: new USB bus registered, assigned bus numb
> er 1
> ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
> ehci_platform ehci_platform.4523: park 0
> ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10
> Dec 2004
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 1 port detected
> ehci_platform ehci_platform.16781: EHCI Host Controller
> ehci_platform ehci_platform.16781: new USB bus registered, assigned bus num
> ber 2
> ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
> ehci_platform ehci_platform.16781: park 0
> ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 1
> 0 Dec 2004
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 1 port detected
> USB Universal Host Controller Interface driver v2.2
> Initializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.01:USB HID core driver
> mice: PS/2 mouse device common for all mice
> md: raid0 personality registered as nr 2
> md: raid1 personality registered as nr 3
> md: raid5 personality registered as nr 4
> raid5: measuring checksumming speed
> arm4regs : 304.000 MB/sec
> 8regs : 215.200 MB/sec
> 32regs : 249.200 MB/sec
> raid5: using function: arm4regs (304.000 MB/sec)
> md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
> Buffalo Platform Linux Driver(Light) 0.01 installed.
> MICON ctrl (C) BUFFALO INC. V.1.00 installed.
> Kernel event proc (C) BUFFALO INC. V.1.00 installed.
> MICON V2 (C) BUFFALO INC. V.1.00 installed.
> NET: Registered protocol family 2
> IP: routing cache hash table of 1024 buckets, 8Kbytes
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> md: Autodetecting RAID arrays.
> md: autorun ...
> md: ... autorun DONE.
> Empty flash at 0x00df85f8 ends at 0x00df8800
> VFS: Mounted root (jffs2 filesystem).
> Freeing init memory: 112K
> --- rcStart (NANDroot) ---
> ===== Starting MountSystemFolders =====
> mounting procfs ... [Success]
> mounting sysfs ... [Success]
> mouting usbfs ... [Success]
> remouting rootfs ... [Success]
> mounting all devices ... [Success]
>
>
> ===== Starting checkroot.sh =====
> rm: /var/lock/perfmon: is a directory
> rm: /var/lock/printing: is a directory
> rm: /var/lock/subsys: is a directory
> [Success]
>
>
> ===== Starting Kevent.sh =====
> [Success]
>
>
> ===== Starting mount_share.sh =====
> Mounting /dev/sda4 on /mnt/disk1 as a xfs file system.
> XFS mounting filesystem sda4
> Starting XFS recovery on filesystem: sda4 (dev: sda4)
> Ending XFS recovery on filesystem: sda4 (dev: sda4)
> Success.
>
> Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
> Success.
>
> [Success]
>
>
> ===== Starting sethostname.sh =====
> hostname is setted to KUROBOX-PRO
> [Success]
>
>
> ===== Starting networking.sh =====
> create network files..
> IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
> killall: dhcpcd: no process killed
> route: SIOC[ADD|DEL]RT: No such process
> Configuration network interface: lo eth0
> requesting DHCP tout=30[s]
> eth0: link down
> eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
> /etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info up
> dhcpcd.exe: interface eth0 has been configured with old IP=192.168.1.12
> hostname is setted to KUROBOX-PRO
> [Success]
>
>
> ===== Starting httpd.sh =====
> [Success]
>
>
> ===== Starting telnet.sh =====
> [Success]
>
>
> ===== Starting inetd.sh =====
> [Success]
>
>
> ===== Starting smb.sh =====
> $Starting SMB services:
> $Starting NMB services:
> [Success]
>
>
> ===== Starting clientUtil_servd.sh =====
> Starting clientUtil_server:starting on eth0
> [Success]
>
>
> ===== Starting bootcomplete.sh =====
> [Success]
>
>
> ===== Starting FanController.sh =====
> [Success]
>
>
> ===== Starting boss.sh =====
>
> ...''''..
> '-~~(~~'' .~<shDBDhz+(-.
> .~+sDDBNBDhhszDBNNNNBNNNBDs<-
> ~sBNNNNNNNNNNNNNNNNNNNNNNNNNBs<'
> -=DNNBNNNNNNNNNNNNNNNNNBNNNNNNNNBz<'
> .~zNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNz~
> '~hBNNNNBNNNNNNNNNNNNNNNNNNNNNNNNNNNNNND+'
> (hNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNBs-
> .~zNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNBNNBNNNNNNBs
> ~sBNNNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNNNNNNNz
> (+DNNNNNNNNNNNNNNNNNNNNNNDzNNNNNhzDNNBNNNNNNNNBs
> (sNNNNNNNNNNNNNNNNNNNNNNB=~hNNNN=~(sDNNNNNNNNNND
> (+DNNNNNNNNNNNNNNNNNNNNNNs'.=NNNNz- '(zDNNNNNNNNNz
> ~=BNNNNNNNNNNNNNNNNNNNNND- .=BNNNN<. .(hNNNNNNNNB
> ~sNNNNNNNNNNNNNNNNNNNNND+. .+BNNNN+' ~sBNNNNNNN
> (zNNNNNNNNNNNNNNNNNNNNND' ..+BNBNB=- .+BNNNNNNh
> (zNNNNNNNNNNNNNNNNNNNBB= . 'hNBBNs+- '+DNNNBND
> (sNNNNNNNNNNNNNNNNNNNND( -DhDBN+<- . '=NNNNNB
> ~+DNNBNNNNNNNNNNNNNNNNz' '=D=Dhh+(' . ~DBNNNB
> ~(sNNNNNNNNNNNNNNNNNNNz. -hs(zz+<(' . .=NNNNN
> ~=NNBBBBNNNNNNNNNNNNB= '==-=+s((~. .~BNNNB
> ~=Nhs<+++hNNNNNNNNBz<- .~=-.s(+-(- 'hBNND
> =Ds+hz( ~hNNNNNNND+'..-+'.-((('<~''... -hNNNNDs
> ~+z(BN=. .<BNNNNBhhDD=+<~. ~-=shBBDhz+(' -sBNNNBBNBz
> ~(=z(BD- '~~hBNNNs~-(<zDDs+~(shzssszDBNDh=<<sBNNNNNNNBN
> ~~+s<z=.-zh~sNNND<. .''<zhhh==shDBNNNNNNNBDDNNNNNNNNNh
> ~~<ss+<.zBBs~zND+' ..-+zDBNNNNNNNNNNNhzNNNNNNNNND+
> ~~(=h<<'+DBz-sBs~ . (BBNNNNNNNNNz-<BBNNBNNND=
> ~(~<zss(('(z<sD+' ~DNNNNNNNNNz~ 'sNNNNNNDs
> ~(=Ds=<...-(h<. . ..<BNNNNNNNNz~ -hNNNBh
> ~(hNs(. =- .=BNNNNNBNs- .(hs==
> ''<BNz~ '. .(hBNNBDz<' .~''-
> -hNNh(. '.. .'<<(++~ . -''.
> 'hBNB+' ' -+('. .-''.
> 'zDNz( '. ~+<-'''..''. .-.
> ..~(-. .'. .~+(. ..''--''.
> ''. .'+<~ '~.
> ..... .-' .'---(~~~(<~.
> ..'. .((---'-~~(~
> .'. '+s=(-'-(+. < Let's start a KURO-BOX!
> .... .(hBDzDD=. and have a fun time...
> ..'.. .'<sDh+.
> .''.. . ..-- .
> ..''.. ...
> ....... .'.
> ..''..'-'..
> ...
>
>
> [Success]
>
>
> KUROUTOSHIKOU KUROBOX Series KUROBOX/PRO(KOSHO)
> KUROBOX-PRO login:
----
最終更新日：&date()
