玄箱PROパッチ適用
私のようにswat不具合を抱えた玄箱PROを持っている場合は必要になる作業です。ここではTFTPを使用したパッチ適用（ファームウェア・バージョンアップ）です。これもシリアルコンソールなしにはできません。
- TFTPサーバー Poor TFTP Server for WIN32をダウンロードして展開
- ptftp32.exeを実行
- Timeoutは60秒に設定しておく
- 同じディレクトリにinitrd.buffaloとuImage.buffaloを配置しておく
- シリアルコンソールからリブートする
KUROBOX-PRO:~# reboot
- PCのアドレスが192.168.1.4でさっき玄箱PROをブートしたときのアドレスが192.168.1.12だったのでserveripにはPCのアドレス、ipaddrには玄箱PROのアドレスを設定
Marvell>> setenv serverip 192.168.1.4
Marvell>> setenv ipaddr 192.168.1.12
Marvell>> tftp $(default_kernel_addr) $(kernel)
Using egiga0 device
TFTP from server 192.168.1.4; our IP address is 192.168.1.12
Filename 'uImage.buffalo'.
Load address: 0x100000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###############
done
Bytes transferred = 1736612 (1a7fa4 hex)
Marvell>> setenv bootargs '$(bootargs_base) $(bootargs_root) rw
initrd=0x02000040,20M panic=5 $(buffalo_ver)'
Marvell>> bootm $(default_kernel_addr) $(default_initrd_addr)
<<stop_sound>>
## Booting image at 00100000 ...
Image Name: Linux-2.6.12.6-arm1
Created: 2007-04-10 13:45:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1736548 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02000000 ...
Image Name: initrd
Created: 2007-04-10 13:46:52 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 19286692 Bytes = 18.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... Bad Data CRC
bootm fail.
<<system_not_found>>
Using egiga0 device
TFTP from server 192.168.1.4; our IP address is 192.168.1.12
Filename 'uImage.buffalo'.
Load address: 0x100000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
###############
done
Bytes transferred = 1736612 (1a7fa4 hex)
Using egiga0 device
TFTP from server 192.168.1.4; our IP address is 192.168.1.12
Filename 'initrd.buffalo'.
Load address: 0x2000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
##############################################################
done
Bytes transferred = 19286756 (1264ae4 hex)
<<stop_sound>>
## Booting image at 00100000 ...
Image Name: Linux-2.6.12.6-arm1
Created: 2007-04-10 13:45:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1736548 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 02000000 ...
Image Name: initrd
Created: 2007-04-10 13:46:52 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 19286692 Bytes = 18.4 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/sda2 rw panic=5 rw initrd=0x02000040,20M
panic=5 BOOTVER=1.091
CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
Uncompressing Linux........................................................
......................................................... done, booting the
kernel.
Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release)
(CodeSourcery
ARM 2005q3-2)) #27 Tue Apr 10 22:47:16 JST 2007
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw panic=5 rw
initrd=0x02000040,20M panic=5 BOOTVER=1.091
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 105600KB available (3037K code, 426K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an
initrd
Freeing initrd memory: 20480K
NET: Registered protocol family 16
serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
config_device_cs Error : Unknown board
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
DEVICE_CS0 ....base fa000000, size 2MB
DEVICE_CS1 ....base f4000000, size 32MB
DEVICE_CS2 ....base fa800000, size 1MB
DEV_BOOCS ....base ff800000, size 8MB
CRYPTO ENG ....no such
Flash bankwidth 1, base ff800000, size 400000
KUROBOX FLASH size 4096[KB]
Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_
BOARD_KUROBOX Soc: 88F5182 A2
Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c3403bc0
Marvell USB EHCI Host controller #1: c3403a40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Use the XOR engines (offloading) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
o copy user to/from kernel buffers
Number of XOR engines to use: 2
cesadev_init(c00122e4)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (10)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
Vendor: Hitachi Model: HDT725050VLA360 Rev: V56O
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
physmap flash device: 400000 at ff800000
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Debug nand_scan : nand_flash_ids[i].pagesize is exist
Debug nand_scan : mtd->erasesize=0x00020000
Debug nand_scan : mtd->oobblock=0x00000800
Debug nand_scan : mtd->oobsize=0x00000040
NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3
V 8-bit)
Scanning device for bad blocks
Bad eraseblock 854 at 0x06ac0000
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00400000 : "uImage"
0x00400000-0x04400000 : "rootfs"
0x04400000-0x10000000 : "extra"
usbmon: debugs is not available
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus numb
er 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10
Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus num
ber 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 1
0 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
arm4regs : 308.800 MB/sec
8regs : 217.600 MB/sec
32regs : 252.400 MB/sec
raid5: using function: arm4regs (308.800 MB/sec)
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Buffalo Platform Linux Driver(Light) 0.01 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
---- in linuxrc ---
proc mount success
libbuffalo mount success
-RamdiskRoot-
-- linuxrc finished. --
Freeing init memory: 112K
init started: BusyBox v1.2.2 (2007.01.15-11:18+0000) multi-call binary
Starting pid 242, console /dev/ttyS0: '/etc/init.d/rcS'
--- rcStart (initrd) ---
===== Starting MountSystemFolders =====
mounting procfs ... [Success]
mounting sysfs ... [Success]
remounting rootfs ... [Success]
mounting all devices ... [Success]
--MountNandDevice--
===== Starting Kevent.sh =====
[Success]
===== Starting networking.sh =====
Deconfiguration network interface: lo eth0
killall: dhcpcd: no process killed
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
eth0: link down
eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
/etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info new
dhcpcd.exe: interface eth0 has been configured with new IP=192.168.1.12
hostname is setted to KUROBOX-PRO
[Success]
===== Starting sethostname.sh =====
hostname is setted to KUROBOX-PRO
[Success]
===== Starting clientUtil_servd.sh =====
Starting clientUtil_server:starting on eth0
start at debug mode
clientUtil_server Ver.1.01
listen device name = eth0
[Success]
Starting pid 484, console /dev/ttyS0: '/sbin/getty'
KUROBOX-PRO login:
}
~ # update_mtd.sh all
***** Cleaning and collect badlist /dev/mtd1 *****
***** copying /boot/uImage.buffalo to /dev/mtd1 *****
***** Cleaning /dev/mtdchar2 *****
***** Writing /boot/nandrootfs.jffs2 to /dev/mtdchar2 *****
***** copying /boot/u-boot.bin to /dev/mtd0 *****
480+1 records in
480+1 records out
***** Cleaning /dev/mtdchar3 *****
Done.
~ #
~ # reboot
Orion1 CPU = Low
=== KURO U-Boot. ===
** LOADER **
** KUROBOX BOARD: KURO_BOX LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
NAND: 256 MB
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 500Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1118 phy
Found boot image
hit any key to switch tftp boot.
Hit any key to stop autoboot: 0
<<system_bootend>>
Hit any key to stop autoboot: 0
Loading from device 0: <NULL> at 0xfa000000 (offset 0x20000)
Image Name: Linux-2.6.12.6-arm1
Created: 2007-04-10 13:45:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1736548 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
<<stop_sound>>
## Booting image at 00100000 ...
Image Name: Linux-2.6.12.6-arm1
Created: 2007-04-10 13:45:13 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1736548 Bytes = 1.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BOOTVER=1.091
CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
Uncompressing Linux........................................................
......................................................... done, booting the
kernel.
Linux version 2.6.12.6-arm1 (root@dev-hara) (gcc version 3.4.4 (release) (C
odeSourcery
ARM 2005q3-2)) #27 Tue Apr 10 22:47:16 JST 2007
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rw panic=5 BO
OTVER=1.091
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 126208KB available (3037K code, 426K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
config_device_cs Error : Unknown board
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
DEVICE_CS0 ....base fa000000, size 2MB
DEVICE_CS1 ....base f4000000, size 32MB
DEVICE_CS2 ....base fa800000, size 1MB
DEV_BOOCS ....base ff800000, size 8MB
CRYPTO ENG ....no such
Flash bankwidth 1, base ff800000, size 400000
KUROBOX FLASH size 4096[KB]
Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_BO
ARD_KUROBOX Soc: 88F5182 A2
Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c04e4b00
Marvell USB EHCI Host controller #1: c04e4a40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Use the XOR engines (offloading) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
o copy user to/from kernel buffers
Number of XOR engines to use: 2
cesadev_init(c00122e4)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
SGI XFS with no debug enabled
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (10)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
Vendor: Hitachi Model: HDT725050VLA360 Rev: V56O
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
physmap flash device: 400000 at ff800000
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
RedBoot partition parsing not available
Debug nand_scan : nand_flash_ids[i].pagesize is exist
Debug nand_scan : mtd->erasesize=0x00020000
Debug nand_scan : mtd->oobblock=0x00000800
Debug nand_scan : mtd->oobsize=0x00000040
NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3
V 8-bit)
Scanning device for bad blocks
Bad eraseblock 854 at 0x06ac0000
Using static partition definition
Creating 3 MTD partitions on "nand_mtd":
0x00000000-0x00400000 : "uImage"
0x00400000-0x04400000 : "rootfs"
0x04400000-0x10000000 : "extra"
usbmon: debugs is not available
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus numb
er 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10
Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus num
ber 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 1
0 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: raid5 personality registered as nr 4
raid5: measuring checksumming speed
arm4regs : 304.000 MB/sec
8regs : 215.200 MB/sec
32regs : 249.200 MB/sec
raid5: using function: arm4regs (304.000 MB/sec)
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
Buffalo Platform Linux Driver(Light) 0.01 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Empty flash at 0x00df85f8 ends at 0x00df8800
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 112K
--- rcStart (NANDroot) ---
===== Starting MountSystemFolders =====
mounting procfs ... [Success]
mounting sysfs ... [Success]
mouting usbfs ... [Success]
remouting rootfs ... [Success]
mounting all devices ... [Success]
===== Starting checkroot.sh =====
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
[Success]
===== Starting Kevent.sh =====
[Success]
===== Starting mount_share.sh =====
Mounting /dev/sda4 on /mnt/disk1 as a xfs file system.
XFS mounting filesystem sda4
Starting XFS recovery on filesystem: sda4 (dev: sda4)
Ending XFS recovery on filesystem: sda4 (dev: sda4)
Success.
Mounting /dev/mtd3 on /mnt/mtd as a jffs2 file system.
Success.
[Success]
===== Starting sethostname.sh =====
hostname is setted to KUROBOX-PRO
[Success]
===== Starting networking.sh =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
eth0: link down
eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
/etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info up
dhcpcd.exe: interface eth0 has been configured with old IP=192.168.1.12
hostname is setted to KUROBOX-PRO
[Success]
===== Starting httpd.sh =====
[Success]
===== Starting telnet.sh =====
[Success]
===== Starting inetd.sh =====
[Success]
===== Starting smb.sh =====
$Starting SMB services:
$Starting NMB services:
[Success]
===== Starting clientUtil_servd.sh =====
Starting clientUtil_server:starting on eth0
[Success]
===== Starting bootcomplete.sh =====
[Success]
===== Starting FanController.sh =====
[Success]
===== Starting boss.sh =====
...''''..
'-~~(~~'' .~<shDBDhz+(-.
.~+sDDBNBDhhszDBNNNNBNNNBDs<-
~sBNNNNNNNNNNNNNNNNNNNNNNNNNBs<'
-=DNNBNNNNNNNNNNNNNNNNNBNNNNNNNNBz<'
.~zNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNz~
'~hBNNNNBNNNNNNNNNNNNNNNNNNNNNNNNNNNNNND+'
(hNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNBs-
.~zNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNBNNBNNNNNNBs
~sBNNNNNNNNNNNNNNNNNNNNNNNNNNNNBNNNNNNNNNNNNNz
(+DNNNNNNNNNNNNNNNNNNNNNNDzNNNNNhzDNNBNNNNNNNNBs
(sNNNNNNNNNNNNNNNNNNNNNNB=~hNNNN=~(sDNNNNNNNNNND
(+DNNNNNNNNNNNNNNNNNNNNNNs'.=NNNNz- '(zDNNNNNNNNNz
~=BNNNNNNNNNNNNNNNNNNNNND- .=BNNNN<. .(hNNNNNNNNB
~sNNNNNNNNNNNNNNNNNNNNND+. .+BNNNN+' ~sBNNNNNNN
(zNNNNNNNNNNNNNNNNNNNNND' ..+BNBNB=- .+BNNNNNNh
(zNNNNNNNNNNNNNNNNNNNBB= . 'hNBBNs+- '+DNNNBND
(sNNNNNNNNNNNNNNNNNNNND( -DhDBN+<- . '=NNNNNB
~+DNNBNNNNNNNNNNNNNNNNz' '=D=Dhh+(' . ~DBNNNB
~(sNNNNNNNNNNNNNNNNNNNz. -hs(zz+<(' . .=NNNNN
~=NNBBBBNNNNNNNNNNNNB= '==-=+s((~. .~BNNNB
~=Nhs<+++hNNNNNNNNBz<- .~=-.s(+-(- 'hBNND
=Ds+hz( ~hNNNNNNND+'..-+'.-((('<~''... -hNNNNDs
~+z(BN=. .<BNNNNBhhDD=+<~. ~-=shBBDhz+(' -sBNNNBBNBz
~(=z(BD- '~~hBNNNs~-(<zDDs+~(shzssszDBNDh=<<sBNNNNNNNBN
~~+s<z=.-zh~sNNND<. .''<zhhh==shDBNNNNNNNBDDNNNNNNNNNh
~~<ss+<.zBBs~zND+' ..-+zDBNNNNNNNNNNNhzNNNNNNNNND+
~~(=h<<'+DBz-sBs~ . (BBNNNNNNNNNz-<BBNNBNNND=
~(~<zss(('(z<sD+' ~DNNNNNNNNNz~ 'sNNNNNNDs
~(=Ds=<...-(h<. . ..<BNNNNNNNNz~ -hNNNBh
~(hNs(. =- .=BNNNNNBNs- .(hs==
''<BNz~ '. .(hBNNBDz<' .~''-
-hNNh(. '.. .'<<(++~ . -''.
'hBNB+' ' -+('. .-''.
'zDNz( '. ~+<-'''..''. .-.
..~(-. .'. .~+(. ..''--''.
''. .'+<~ '~.
..... .-' .'---(~~~(<~.
..'. .((---'-~~(~
.'. '+s=(-'-(+. < Let's start a KURO-BOX!
.... .(hBDzDD=. and have a fun time...
..'.. .'<sDh+.
.''.. . ..-- .
..''.. ...
....... .'.
..''..'-'..
...
[Success]
KUROUTOSHIKOU KUROBOX Series KUROBOX/PRO(KOSHO)
KUROBOX-PRO login:
最終更新日：2007-05-28
最終更新：2007年05月28日 10:12
