「debian-minirootをセットアップ」の編集履歴（バックアップ）一覧はこちら
追加された行は緑色になります。
削除された行は赤色になります。
*debian-minirootをセットアップ
自力で玄箱PRO仕様のDebian化はなかなか敷居が高そうなのでsushi-k氏が作成されたdebian-minirootを使用します。作業前には事前に[[sushi-k日誌2>http://w3.quake3.jp/sushi-k/wp/?p=93]]で「KURO-BOX/PRO Debian化決定版？」をよく読み、必要な「gnutar_kuropro.gz」「debian_kit.tar.gz」「hddrootfs.tar.gz」「uImage.buffalo」の4ファイルを入手しておきます。
**sushi-k氏のdebian-minirootを準備する
・\\kurobox-pro\shareへdebian_kit.tar.gzとgnutar_kuropro.gzを転送
・GNU tarの導入
> ~ # cd /mnt/disk1
> /mnt/disk1 # rm /bin/tar
> /mnt/disk1 # gzip -dc gnutar_kuropro.gz >/bin/tar
> /mnt/disk1 # chmod a+x /bin/tar
・OABIなmkfs.ext3を含むDebian化キット導入
> /mnt/disk1 # tar xvzpf debian_kit.tar.gz -C /
・\\kurobox-pro\mtd deviceへhddrootfs.tar.gzとuImage.buffaloとChangeMeDevHDDとChangeMyUbootEnvを転送
・HDDを初期化する
> ~ # /usr/local/bin/DiskDelete.sh
**背面INITボタンを押してHDD環境をセットアップする
・背面スイッチを長押しする
・処理が動いているか不安なのでtopでモニタする
> ~ # top
・オレンジのランプが消えたら初期化終了なので一度シャットダウンする
> ~ # shutdown -h
・電源投入
> Orion1 CPU = Low
>
> === KURO U-Boot. ===
> ** LOADER **
> ** KUROBOX BOARD: KURO_BOX LE (CFG_ENV_ADDR=fffff000)
>
>
> U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY
>
> DRAM CS[0] base 0x00000000 size 128MB
> DRAM Total size 128MB
> [256kB@fffc0000] Flash: 256 kB
> Addresses 20M - 0M are saved for the U-Boot usage.
> Mem malloc Initialization (20M - 16M): Done
> NAND: 256 MB
>
> Soc: 88F5182 A2
> CPU: ARM926 (Rev 0) running @ 500Mhz
> Orion 1 streaming disabled
> SysClock = 250Mhz , TClock = 166Mhz
>
>
> USB 0: host mode
> USB 1: host mode
> PCI 0: PCI Express Root Complex Interface
> PCI 1: Conventional PCI, speed = 33000000
> Net: egiga0 [PRIME]
> Using 88E1118 phy
> hit any key to switch tftp boot.
> Hit any key to stop autoboot: 0
> <<system_bootend>>
> Hit any key to stop autoboot: 0
>
> Reset IDE:
> Marvell Serial ATA Adapter
> Integrated Sata device found
> Device 0: OK
> Model: Hitachi HDT725050VLA360 Firm: V56OA52A Ser#:
> VFB400R4C28DDA
> Type: Hard Disk
> Supports 48-bit addressing
> Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
>
> Using device ide0, partition 1
>
> Loading from block device ide device 0, partition 1: Name: hda1
> Type: U-Boot File:/uImage.buffalo
>
> 1717540 bytes read
> <<stop_sound>>
> ## Booting image at 00100000 ...
> Image Name: Linux-2.6.12.6-mda1
> Created: 2007-04-22 7:17:43 UTC
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1717476 Bytes = 1.6 MB
> Load Address: 00008000
> Entry Point: 00008000
> Verifying Checksum ... OK
> OK
>
> Starting kernel ...
>
> arg:console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVER=1.09
> CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
> Uncompressing Linux.......................................................
> ........................................................ done, booting the
> kernel.
> Linux version 2.6.12.6-mda1 (root@kurobox) (gcc version 4.1.2 20061115 (pr
> erelease) (Debian 4.1.1-21)) #2 Sun Apr 22 16:16:39 JST 2007
> CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
> CPU0: D VIVT write-back cache
> CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
> CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
> Machine: MV-88fxx81
> Using UBoot passing parameters structure
> Sys Clk = 250000000, Tclk = 166664740
> Memory policy: ECC disabled, Data cache writeback
> Built 1 zonelists
> Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVE
> R=1.09
> PID hash table entries: 1024 (order: 10, 16384 bytes)
> Console: colour dummy device 80x30
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Memory: 128MB 0MB 0MB 0MB = 128MB total
> Memory: 126208KB available (2987K code, 421K data, 108K init)
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> NET: Registered protocol family 16
> serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
> config_device_cs Error : Unknown board
>
> CPU Interface
> -------------
> SDRAM_CS0 ....base 00000000, size 128MB
> SDRAM_CS1 ....disable
> SDRAM_CS2 ....disable
> SDRAM_CS3 ....disable
> PEX0_MEM ....base e0000000, size 128MB
> PEX0_IO ....base f2000000, size 1MB
> PCI0_MEM ....base e8000000, size 128MB
> PCI0_IO ....base f2100000, size 1MB
> INTER_REGS ....base f1000000, size 1MB
> DEVICE_CS0 ....base fa000000, size 2MB
> DEVICE_CS1 ....base f4000000, size 32MB
> DEVICE_CS2 ....base fa800000, size 1MB
> DEV_BOOCS ....base ff800000, size 8MB
> CRYPTO ENG ....no such
> Flash bankwidth 1, base ff800000, size 400000
> KUROBOX FLASH size 4096[KB]
>
> Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_B
> OARD_KUROBOX Soc: 88F5182 A2
>
> Detected Tclk 166664740 and SysClk 250000000
> Marvell USB EHCI Host controller #0: c04d5b00
> Marvell USB EHCI Host controller #1: c04d5a40
> pexBarOverlapDetect: winNum 2 overlap current 0
> mvPexInit:Warning :Bar 2 size is illigal
> it will be disabled
> please check Pex and CPU windows configuration
> PCI: bus0: Fast back to back transfers enabled
> PCI: bus1: Fast back to back transfers enabled
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> Use the XOR engines (offloading) for enhancing the following functions:
> o RAID 5 Xor calculation
> o kernel memcpy
> o kenrel memzero
> o copy user to/from kernel buffers
> Number of XOR engines to use: 2
> cesadev_init(c0012240)
> Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
> inotify device minor=63
> JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
> SGI XFS with no debug enabled
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
> ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
> loop: loaded (max 8 devices)
> Marvell Gigabit Ethernet Driver 'egiga':
> o Ethernet descriptors in DRAM
> o DRAM SW cache-coherency
> o Checksum offload enabled
> o Loading network interface ** egiga_init_module (6)
> 'eth0'
> Intergrated Sata device found
> scsi0 : Marvell SCSI to SATA adapter
> scsi1 : Marvell SCSI to SATA adapter
> Vendor: Hitachi Model: HDT725050VLA360 Rev: V56O
> Type: Direct-Access ANSI SCSI revision: 03
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> SCSI device sda: drive cache: write back
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 sda3 sda4
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> physmap flash device: 400000 at ff800000
> Found: SST 39LF020
> phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
> number of JEDEC chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> RedBoot partition parsing not available
> NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,
> 3V 8-bit)
> Scanning device for bad blocks
> Bad eraseblock 854 at 0x06ac0000
> Using static partition definition
> Creating 3 MTD partitions on "nand_mtd":
> 0x00000000-0x00400000 : "uImage"
> 0x00400000-0x04400000 : "rootfs"
> 0x04400000-0x10000000 : "extra"
> usbmon: debugs is not available
> ehci_platform ehci_platform.4523: EHCI Host Controller
> ehci_platform ehci_platform.4523: new USB bus registered, assigned bus num
> ber 1
> ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
> ehci_platform ehci_platform.4523: park 0
> ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 1
> 0 Dec 2004
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 1 port detected
> ehci_platform ehci_platform.16781: EHCI Host Controller
> ehci_platform ehci_platform.16781: new USB bus registered, assigned bus nu
> mber 2
> ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
> ehci_platform ehci_platform.16781: park 0
> ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver
> 10 Dec 2004
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 1 port detected
> USB Universal Host Controller Interface driver v2.2
> Initializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.01:USB HID core driver
> mice: PS/2 mouse device common for all mice
> md: raid0 personality registered as nr 2
> md: raid1 personality registered as nr 3
> md: raid5 personality registered as nr 4
> raid5: measuring checksumming speed
> arm4regs : 309.200 MB/sec
> 8regs : 269.200 MB/sec
> 32regs : 200.000 MB/sec
> raid5: using function: arm4regs (309.200 MB/sec)
> md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
> Buffalo Platform Linux Driver(Light) 0.01 installed.
> MICON ctrl (C) BUFFALO INC. V.1.00 installed.
> Kernel event proc (C) BUFFALO INC. V.1.00 installed.
> MICON V2 (C) BUFFALO INC. V.1.00 installed.
> NET: Registered protocol family 2
> IP: routing cache hash table of 1024 buckets, 8Kbytes
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> md: Autodetecting RAID arrays.
> md: autorun ...
> md: ... autorun DONE.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on sda2, internal journal
> EXT3-fs: recovery complete.
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem).
> Freeing init memory: 108K
> INIT: version 2.86 booting
> Activating swap...Adding 136544k swap on /dev/sda3. Priority:-1 extents:1
> done.
> Checking root file system...fsck 1.40-WIP (14-Nov-2006)
> /dev/sda2 has gone 36051 days without being checked, check forced.
> /dev/sda2: 8298/367616 files (0.8% non-contiguous), 204892/2939892 blocks
> done.
> EXT3 FS on sda2, internal journal
> Setting the system clock..
> Cleaning up ifupdown....
> Loading device-mapper support.
> Checking file systems...fsck 1.40-WIP (14-Nov-2006)
> /dev/sda1: recovering journal
> /dev/sda1: clean, 12/7056 files, 6718/56196 blocks
> done.
> Setting kernel variables...done.
> Mounting local filesystems...kjournald starting. Commit interval 5 second
> s
> EXT3 FS on sda1, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> done.
> Activating swapfile swap...done.
> Setting up networking....
> Configuring network interfaces...eth0: link down
> done.
> eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
> INIT: Entering runlevel: 2
> Starting system log daemon: syslogd.
> Starting kernel log daemon: klogd.
> * Not starting internet superserver: no services enabled.
> Starting OpenBSD Secure Shell server: sshd.
> Starting periodic command scheduler: crond.
>
> Debian GNU/Linux 4.0 kurobox ttyS0
>
> kurobox login: root
> Password:
> Last login: Fri Mar 9 16:42:48 2007 from localhost.localdomain on pts/0
> Linux kurobox 2.6.12.6-mda1 #2 Sun Apr 22 16:16:39 JST 2007 armv5tejl
>
> The programs included with the Debian GNU/Linux system are free software;
> the exact distribution terms for each program are described in the
> individual files in /usr/share/doc/*/copyright.
>
> Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
> permitted by applicable law.
> kurobox:~#
・ホスト名をKUROBOX-PROに変更する(あとで再起動したあとに有効になる)
> kurobox:~# vi /etc/hostname
> #kurobox
> KUROBOX-PRO
・パーミッションの設定を追加する
> chmod 666 /dev/tty
> chmod 4755 /bin/ping
・NANDブート時と同じ/mntの構成にしておく
> mkdir /mnt/authtest
> mkdir /mnt/boot
> mkdir /mnt/disk1
> mkdir /mnt/mtd
> mkdir /mnt/nfs
> mkdir /mnt/ram
> mkdir /mnt/root
> mkdir /mnt/rootfs
> mkdir /mnt/usbdisk1
> mkdir /mnt/usbdisk2
・ブートしたときに/dev/sda4を/mnt/disk1にマウントするようにfstabを編集する
> kurobox:~# vi /etc/fstab
> /dev/sda4 /mnt/disk1 ext3 defaults 1 1
・ネットワークの設定をDHCPに戻す
> kurobox:~# vi etc/network/interfaces
> # Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or
> # /usr/share/doc/ifupdown/examples for more information.
>
> auto lo
> iface lo inet loopback
>
> auto eth0
> iface eth0 inet dhcp
> kurobox:~# ifdown eth0
> kurobox:~# ifup eth0
・一度リブートしてみる
・shutdown -h now コマンドでパワーダウンだけで終わってしまうので電源断できるようにする
> kurobox:~# vi /etc/default/halt
> #HALT=poweroff
> HALT=halt
・一度シャットダウンしてみる
> kurobox:~# shutdown -h now
----
最終更新日：&date()
*debian-minirootをセットアップ
自力で玄箱PRO仕様のDebian化はなかなか敷居が高そうなのでsushi-k氏が作成されたdebian-minirootを使用します。作業前には事前に[[sushi-k日誌2>http://w3.quake3.jp/sushi-k/wp/?p=93]]で「KURO-BOX/PRO Debian化決定版？」をよく読み、必要な「gnutar_kuropro.gz」「debian_kit.tar.gz」「hddrootfs.tar.gz」「uImage.buffalo」の4ファイルを入手しておきます。
**sushi-k氏のdebian-minirootを準備する
・\\kurobox-pro\shareへdebian_kit.tar.gzとgnutar_kuropro.gzを転送
・GNU tarの導入
> ~ # cd /mnt/disk1
> /mnt/disk1 # rm /bin/tar
> /mnt/disk1 # gzip -dc gnutar_kuropro.gz >/bin/tar
> /mnt/disk1 # chmod a+x /bin/tar
・OABIなmkfs.ext3を含むDebian化キット導入
> /mnt/disk1 # tar xvzpf debian_kit.tar.gz -C /
・\\kurobox-pro\mtd deviceへhddrootfs.tar.gzとuImage.buffaloとChangeMeDevHDDとChangeMyUbootEnvを転送
・HDDを初期化する
> ~ # /usr/local/bin/DiskDelete.sh
**背面INITボタンを押してHDD環境をセットアップする
・背面スイッチを長押しする
・処理が動いているか不安なのでtopでモニタする
> ~ # top
・オレンジのランプが消えたら初期化終了なので一度シャットダウンする
> ~ # shutdown -h
・電源投入
> Orion1 CPU = Low
>
> === KURO U-Boot. ===
> ** LOADER **
> ** KUROBOX BOARD: KURO_BOX LE (CFG_ENV_ADDR=fffff000)
>
>
> U-Boot 1.1.1 (Apr 10 2007 - 18:10:08) Marvell version: 1.12.1 - TINY
>
> DRAM CS[0] base 0x00000000 size 128MB
> DRAM Total size 128MB
> [256kB@fffc0000] Flash: 256 kB
> Addresses 20M - 0M are saved for the U-Boot usage.
> Mem malloc Initialization (20M - 16M): Done
> NAND: 256 MB
>
> Soc: 88F5182 A2
> CPU: ARM926 (Rev 0) running @ 500Mhz
> Orion 1 streaming disabled
> SysClock = 250Mhz , TClock = 166Mhz
>
>
> USB 0: host mode
> USB 1: host mode
> PCI 0: PCI Express Root Complex Interface
> PCI 1: Conventional PCI, speed = 33000000
> Net: egiga0 [PRIME]
> Using 88E1118 phy
> hit any key to switch tftp boot.
> Hit any key to stop autoboot: 0
> <<system_bootend>>
> Hit any key to stop autoboot: 0
>
> Reset IDE:
> Marvell Serial ATA Adapter
> Integrated Sata device found
> Device 0: OK
> Model: Hitachi HDT725050VLA360 Firm: V56OA52A Ser#:
> VFB400R4C28DDA
> Type: Hard Disk
> Supports 48-bit addressing
> Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
>
> Using device ide0, partition 1
>
> Loading from block device ide device 0, partition 1: Name: hda1
> Type: U-Boot File:/uImage.buffalo
>
> 1717540 bytes read
> <<stop_sound>>
> ## Booting image at 00100000 ...
> Image Name: Linux-2.6.12.6-mda1
> Created: 2007-04-22 7:17:43 UTC
> Image Type: ARM Linux Kernel Image (uncompressed)
> Data Size: 1717476 Bytes = 1.6 MB
> Load Address: 00008000
> Entry Point: 00008000
> Verifying Checksum ... OK
> OK
>
> Starting kernel ...
>
> arg:console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVER=1.09
> CONFIG_KUROBOX_PLATFORM CONFIG_KUROBOX_KUROBOX ---
> Uncompressing Linux.......................................................
> ........................................................ done, booting the
> kernel.
> Linux version 2.6.12.6-mda1 (root@kurobox) (gcc version 4.1.2 20061115 (pr
> erelease) (Debian 4.1.1-21)) #2 Sun Apr 22 16:16:39 JST 2007
> CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
> CPU0: D VIVT write-back cache
> CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
> CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
> Machine: MV-88fxx81
> Using UBoot passing parameters structure
> Sys Clk = 250000000, Tclk = 166664740
> Memory policy: ECC disabled, Data cache writeback
> Built 1 zonelists
> Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVE
> R=1.09
> PID hash table entries: 1024 (order: 10, 16384 bytes)
> Console: colour dummy device 80x30
> Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> Memory: 128MB 0MB 0MB 0MB = 128MB total
> Memory: 126208KB available (2987K code, 421K data, 108K init)
> Mount-cache hash table entries: 512
> CPU: Testing write buffer coherency: ok
> NET: Registered protocol family 16
> serial_initialize_ttyS1 (Debug): ttyS1 is initialized.
> config_device_cs Error : Unknown board
>
> CPU Interface
> -------------
> SDRAM_CS0 ....base 00000000, size 128MB
> SDRAM_CS1 ....disable
> SDRAM_CS2 ....disable
> SDRAM_CS3 ....disable
> PEX0_MEM ....base e0000000, size 128MB
> PEX0_IO ....base f2000000, size 1MB
> PCI0_MEM ....base e8000000, size 128MB
> PCI0_IO ....base f2100000, size 1MB
> INTER_REGS ....base f1000000, size 1MB
> DEVICE_CS0 ....base fa000000, size 2MB
> DEVICE_CS1 ....base f4000000, size 32MB
> DEVICE_CS2 ....base fa800000, size 1MB
> DEV_BOOCS ....base ff800000, size 8MB
> CRYPTO ENG ....no such
> Flash bankwidth 1, base ff800000, size 400000
> KUROBOX FLASH size 4096[KB]
>
> Marvell Development Board (LSP Version 1.10.3.patch5_DB_NAS)-- KUROBOX_B
> OARD_KUROBOX Soc: 88F5182 A2
>
> Detected Tclk 166664740 and SysClk 250000000
> Marvell USB EHCI Host controller #0: c04d5b00
> Marvell USB EHCI Host controller #1: c04d5a40
> pexBarOverlapDetect: winNum 2 overlap current 0
> mvPexInit:Warning :Bar 2 size is illigal
> it will be disabled
> please check Pex and CPU windows configuration
> PCI: bus0: Fast back to back transfers enabled
> PCI: bus1: Fast back to back transfers enabled
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> Use the XOR engines (offloading) for enhancing the following functions:
> o RAID 5 Xor calculation
> o kernel memcpy
> o kenrel memzero
> o copy user to/from kernel buffers
> Number of XOR engines to use: 2
> cesadev_init(c0012240)
> Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
> inotify device minor=63
> JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
> SGI XFS with no debug enabled
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
> ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered
> RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
> loop: loaded (max 8 devices)
> Marvell Gigabit Ethernet Driver 'egiga':
> o Ethernet descriptors in DRAM
> o DRAM SW cache-coherency
> o Checksum offload enabled
> o Loading network interface ** egiga_init_module (6)
> 'eth0'
> Intergrated Sata device found
> scsi0 : Marvell SCSI to SATA adapter
> scsi1 : Marvell SCSI to SATA adapter
> Vendor: Hitachi Model: HDT725050VLA360 Rev: V56O
> Type: Direct-Access ANSI SCSI revision: 03
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> SCSI device sda: drive cache: write back
> SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2 sda3 sda4
> Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
> physmap flash device: 400000 at ff800000
> Found: SST 39LF020
> phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
> number of JEDEC chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> RedBoot partition parsing not available
> NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,
> 3V 8-bit)
> Scanning device for bad blocks
> Bad eraseblock 854 at 0x06ac0000
> Using static partition definition
> Creating 3 MTD partitions on "nand_mtd":
> 0x00000000-0x00400000 : "uImage"
> 0x00400000-0x04400000 : "rootfs"
> 0x04400000-0x10000000 : "extra"
> usbmon: debugs is not available
> ehci_platform ehci_platform.4523: EHCI Host Controller
> ehci_platform ehci_platform.4523: new USB bus registered, assigned bus num
> ber 1
> ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
> ehci_platform ehci_platform.4523: park 0
> ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 1
> 0 Dec 2004
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 1 port detected
> ehci_platform ehci_platform.16781: EHCI Host Controller
> ehci_platform ehci_platform.16781: new USB bus registered, assigned bus nu
> mber 2
> ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
> ehci_platform ehci_platform.16781: park 0
> ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver
> 10 Dec 2004
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 1 port detected
> USB Universal Host Controller Interface driver v2.2
> Initializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.01:USB HID core driver
> mice: PS/2 mouse device common for all mice
> md: raid0 personality registered as nr 2
> md: raid1 personality registered as nr 3
> md: raid5 personality registered as nr 4
> raid5: measuring checksumming speed
> arm4regs : 309.200 MB/sec
> 8regs : 269.200 MB/sec
> 32regs : 200.000 MB/sec
> raid5: using function: arm4regs (309.200 MB/sec)
> md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
> Buffalo Platform Linux Driver(Light) 0.01 installed.
> MICON ctrl (C) BUFFALO INC. V.1.00 installed.
> Kernel event proc (C) BUFFALO INC. V.1.00 installed.
> MICON V2 (C) BUFFALO INC. V.1.00 installed.
> NET: Registered protocol family 2
> IP: routing cache hash table of 1024 buckets, 8Kbytes
> TCP established hash table entries: 8192 (order: 4, 65536 bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 8192 bind 8192)
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> md: Autodetecting RAID arrays.
> md: autorun ...
> md: ... autorun DONE.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on sda2, internal journal
> EXT3-fs: recovery complete.
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem).
> Freeing init memory: 108K
> INIT: version 2.86 booting
> Activating swap...Adding 136544k swap on /dev/sda3. Priority:-1 extents:1
> done.
> Checking root file system...fsck 1.40-WIP (14-Nov-2006)
> /dev/sda2 has gone 36051 days without being checked, check forced.
> /dev/sda2: 8298/367616 files (0.8% non-contiguous), 204892/2939892 blocks
> done.
> EXT3 FS on sda2, internal journal
> Setting the system clock..
> Cleaning up ifupdown....
> Loading device-mapper support.
> Checking file systems...fsck 1.40-WIP (14-Nov-2006)
> /dev/sda1: recovering journal
> /dev/sda1: clean, 12/7056 files, 6718/56196 blocks
> done.
> Setting kernel variables...done.
> Mounting local filesystems...kjournald starting. Commit interval 5 second
> s
> EXT3 FS on sda1, internal journal
> EXT3-fs: mounted filesystem with ordered data mode.
> done.
> Activating swapfile swap...done.
> Setting up networking....
> Configuring network interfaces...eth0: link down
> done.
> eth0: link up<5>, full duplex<5>, speed 100 Mbps<5>
> INIT: Entering runlevel: 2
> Starting system log daemon: syslogd.
> Starting kernel log daemon: klogd.
> * Not starting internet superserver: no services enabled.
> Starting OpenBSD Secure Shell server: sshd.
> Starting periodic command scheduler: crond.
>
> Debian GNU/Linux 4.0 kurobox ttyS0
>
> kurobox login: root
> Password:
> Last login: Fri Mar 9 16:42:48 2007 from localhost.localdomain on pts/0
> Linux kurobox 2.6.12.6-mda1 #2 Sun Apr 22 16:16:39 JST 2007 armv5tejl
>
> The programs included with the Debian GNU/Linux system are free software;
> the exact distribution terms for each program are described in the
> individual files in /usr/share/doc/*/copyright.
>
> Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
> permitted by applicable law.
> kurobox:~#
・ホスト名をKUROBOX-PROに変更する(あとで再起動したあとに有効になる)
> kurobox:~# vi /etc/hostname
> #kurobox
> KUROBOX-PRO
> kurobox:~# vi /etc/hosts
> #127.0.0.1 localhost.localdomain localhost kurobox
> 127.0.0.1 localhost.localdomain localhost KUROBOX-PRO
・パーミッションの設定を追加する
> chmod 666 /dev/tty
> chmod 4755 /bin/ping
・NANDブート時と同じ/mntの構成にしておく
> mkdir /mnt/authtest
> mkdir /mnt/boot
> mkdir /mnt/disk1
> mkdir /mnt/mtd
> mkdir /mnt/nfs
> mkdir /mnt/ram
> mkdir /mnt/root
> mkdir /mnt/rootfs
> mkdir /mnt/usbdisk1
> mkdir /mnt/usbdisk2
・ブートしたときに/dev/sda4を/mnt/disk1にマウントするようにfstabを編集する
> kurobox:~# vi /etc/fstab
> /dev/sda4 /mnt/disk1 ext3 defaults 1 1
・ネットワークの設定をDHCPに戻す
> kurobox:~# vi etc/network/interfaces
> # Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or
> # /usr/share/doc/ifupdown/examples for more information.
>
> auto lo
> iface lo inet loopback
>
> auto eth0
> iface eth0 inet dhcp
> kurobox:~# ifdown eth0
> kurobox:~# ifup eth0
・一度リブートしてみる
・shutdown -h now コマンドでパワーダウンだけで終わってしまうので電源断できるようにする
> kurobox:~# vi /etc/default/halt
> #HALT=poweroff
> HALT=halt
・一度シャットダウンしてみる
> kurobox:~# shutdown -h now
----
最終更新日：&date()
